Internal Wall Insulation in Ayr: Solid Sandstone, Insulated to Last
Sandstone tenements, villas and cottages built before 1919, insulated in hemp, wood wool and lime so damp can still get out of the stone. Surveyed and designed for your wall type from layers already modelled for Scottish stone, with Home Energy Scotland grant funding if you qualify.
Top-floor tenement, conservation area
-
Stripped to the stone
-
A lime parge
-
Hemp in the frame
-
Wood-wool board
-
Lime plaster with mesh
-
Finished and painted
Illustration: a vapour-open system on a stone wall
-
Stripped to the stone
-
A lime parge
-
Hemp in the frame
-
Wood-wool board
-
Lime plaster with mesh
-
Finished and painted
Solid Wall Insulation in Ayr: What the Weather Side Does to a Stone Wall
You want your Ayr stone house warm, and the warnings you have read about trapped damp make you wary of insulating it.
-
On this coast a west-facing gable takes January rain straight off the Firth of Clyde, while the sheltered wall round the corner barely gets wet.
-
A common mistake is one system fitted everywhere, with no read of the wall it goes onto.
Around 98% of external and 29% of internal wall insulation fitted under ECO4 and GBIS carried major defects, across more than 30,000 homes (National Audit Office, October 2025).
We design every Ayr job to give you both, warm rooms and a wall that stays sound.
A stone wall on this coast has to dry out between storms, so every layer we build is vapour-open, the accurate term for “breathable”.
That is how we fit internal wall insulation on the stone houses we line in Ayr.
Through an Ayr winter your rooms stay warm, and the stone still dries out between storms.
How we design internal wall insulation in Ayr
We design each build-up for how your wall is made and how it handles water. The six steps below show what a typical heritage install in Ayr involves.
-
Survey and design
You get a full survey and a design for your wall type. We check the design against WUFI, software that has modelled how damp moves through each type of Scottish wall in weather like Ayr’s, so we know the moisture risk up front.
-
Bare stone, then a lime base coat
Where the old plaster has to go, we take the wall to bare stone and spread a thin lime coat over it. The lime evens out how the stone takes up and gives off damp.
-
Vapour-open insulation
Typically dual-layer IndiTherm hemp (or wood wool / Sisalwool) set in a timber frame, vapour-permeable the whole way through.
-
Wood-wool board and lime plaster
A wood-wool board and a two-coat lime plaster finish with mesh, so the whole build-up stays vapour-open.
-
Membranes only where modelled
Where the modelling shows a wall needs it, usually rendered brick or brick that takes in little water, we add a sheet that keeps room moisture out.
-
Finishes, paints and EPC
Guidance on vapour-open mineral or silicate paints and aftercare, plus a post-installation EPC where relevant.
The honest bit: period features
Existing cornicing, shutters and panelling on the walls we insulate must be removed and cannot be saved. The cornicing is recreated in lime once the insulation is in, and at the survey we agree exactly who does that work, replacement panelling included.
Inside the wall
Your wall, insulated layer by layer
Each card shows one build going onto a wall, from bare masonry to a finished room, in the order our fitters work. The pictures are illustrations.
Illustration: heritage system
-
Stripped to the stone
Our fitters strip the old plaster and timber laths back to bare sandstone, so no hidden wood is left to rot. Cornicing on these walls comes down too, and is remade in lime after the insulation goes in.
-
A lime parge
Then a coat of lime, called a parge, goes over the stone. It fills the hollows where damp air could sit and turn to water.
-
Hemp in the frame
Our fitters press two 50mm layers of Scottish-made IndiTherm hemp into a 45mm timber frame fixed over the lime. This is the layer that keeps the heat in your room.
-
Wood-wool board
Wood-wool board, a stiff sheet of bound wood shavings, goes over the hemp next. It gives the lime plaster a solid face to grip and still lets moisture pass through.
-
Lime plaster with mesh
Lime plaster goes on next, with a mesh bedded into it.
-
Finished and painted
A smooth lime finish leaves the wall about 120mm further into the room than before. At handover you get paint guidance, so the finish keeps letting the wall dry.
Hemp, wood wool and lime on bare sandstone
This vapour-open build suits most solid sandstone walls. Each layer lets moisture pass, so the stone behind it can keep drying out.
Illustration: membrane system
-
Stripped back to brick
The old plaster comes off the inside of the wall, back to the brick.
-
Hemp packed into a frame
Our fitters pack hemp insulation into a timber frame fixed over the brick.
-
The Intello Plus membrane
A Pro Clima Intello Plus membrane goes across the frame to keep room moisture out of the wall.
-
Plasterboard and skim
Plasterboard goes over the membrane, and a skim coat finishes the wall.
Hemp and a membrane for the right brick wall
Some walls are brick, and where that brick is rendered or takes up little water, a sealed build can suit it better.
It finishes in plasterboard and a skim coat, so it goes in faster than the lime build.
At your survey, Calum or Lewis checks each outside wall, and Calum tells you which build each one suits.
Why vapour-open, and why it matters for Scottish stone.
-
1Bare solid stone
Solid sandstone and rubble-stone walls absorb water and let it evaporate off both faces. There is no cavity, membrane or plastic in them, and that works indefinitely as long as the wall keeps drying.
-
2Foil-faced foam board
Foil-faced foam board or sealed foam, glued to the inside of the wall, breaks that. Warm moisture hits a cold sealed layer and condenses, and that trapped condensation is the damp people blame on insulation.
-
3Vapour-open build-up
A vapour-open build-up of lime, hemp and wood wool lets it pass through instead, so the wall stays warm and keeps drying. The brand of insulation matters less than whether anyone designed the build-up. A stone tenement follows the same rules, and we design tenement wall insulation the same way.
The honest comparison
Lime + hemp or wood wool
Barrier membrane + insulation
Sealed foam on solid sandstone
We won’t fix a sealed polystyrene or foam board onto a solid sandstone wall to hit a budget. If that’s what a cheaper number would take, we’ll tell you honestly and recommend against it.
Why internal wall insulation in Ayr is calculated, not guessed
Our designs are built on WUFI modelling, a computer check of how heat and damp pass through each layer over the years a solid wall really needs to dry out, roughly five for brick, ten for stone.
A standard stone wall is matched to a build-up we have already modelled. Before any work starts, you see the modelled moisture risk for a wall like yours as a figure.
What homeowners ask before they commit.
Not when it is designed for the wall. On an Ayr sandstone wall we use vapour-open materials and base the design on modelling of how moisture behaves, so the wall keeps drying. That is also why a vapour-open build-up needs no conventional plastic vapour barrier.
A vapour-open build-up adds some depth. How much depends on the system, on how much space we gain back when the old lath and plaster comes off, and on the depth of the lime parge, which we do not know exactly until we open up. Expect each insulated wall to come in by about 120mm, within 105mm to 125mm, and we go over it room by room at survey.
At the survey we work out the depth for each room you plan to insulate.
Book Your Free Survey ↓On a solid-wall job, yes. To strip the wall back we have to remove the existing cornicing, shutters and panelling in those rooms, and they cannot be saved. The cornicing is recreated in lime once the insulation is in, and at the survey we agree exactly who does that work. The same goes for any replacement shutters or wood panelling you want.
Usually yes. External insulation is normally unacceptable on a sandstone frontage, which is why internal vapour-open systems are the appropriate route. We have worked in conservation areas and will tell you honestly what is feasible.
Mention the listing or the conservation area when you book, so the survey covers what consent will need.
Book Your Free Survey ↓A vapour-open system protects the fabric and improves the EPC, both of which support the value of a period home in Ayr. We will give you a straight view of payback for your situation.
Ballagan Farm, Strathblane
A full renovation of a two-storey farmhouse where the walls were damp from being poorly insulated. We stripped them back to the bare stone, parged them in lime, then insulated with IndiTherm hemp and wood-wool boards before finishing in lime plaster across both the sloping ceilings and the solid sandstone walls. The loft was insulated with Knauf Earthwool 44.
Auchinlay House, Dunblane
An internal wall and room-in-roof project for a homeowner preparing to install a heat pump and make the bedrooms comfortable year round. We used a vapour-permeable build-up of hemp, wood-wool board and lime plaster on the walls, paired with a vapour-closed system of PIR and Superfoil SF19+ on the sloping ceilings and dormers, plus Knauf Earthwool in the upper loft space.
Mount Hope, Bridge of Allan
The client was renovating an old sandstone wing of their period property. We installed a vapour-permeable system of 100mm Sisalwool, wood-wool board and lime plaster across four walls, including one large gable wall where the dropped ceiling was removed to create an insulated vaulted ceiling.
Belhaven Terrace Lane, Glasgow
A West End client looking to improve thermal performance across the whole home. The property was given internal wall insulation across the ground floor and room-in-roof insulation in the upstairs bedrooms. A vapour-open design for the stone walls was paired with vapour-closed insulation in the sloping ceilings, keeping the high-absorption sandstone able to dry while stopping warm, moist air reaching the roof spaces.
Observatory Lane, Glasgow
An internal wall insulation project carried out for a client of Oscar J Murray Architects as part of a whole-house renovation in Glasgow’s West End. We used IndiTherm hemp insulation on the stone walls, dormers and sloped ceilings, finished in lime plaster, with a Pro Clima Intello membrane on the sloping ceilings and Contega Solido airtightness tape around the windows.
Protected, and built to the standard the grant requires.
Every Ayr quote is written for what the stone needs, even when a cheaper board would bring the price down.
-
25-year workmanship guarantee
If our workmanship fails, we come back and put it right.
-
No deposit, pay after completion
Nothing is paid up front, and payment is due within 7 days of completion.
-
TrustMark and PAS 2030 certified
Audited against the grant’s rules, with Calum leading every design and signing off the quote.
-
Our own employed fitters
We use no agency labour, and we turn down work that is not right for the wall.
Internal wall insulation in Ayr: your questions answered.
Straight answers on cost, damp, room loss, grants and conservation areas.
It is insulation fitted to the inside face of a solid wall, used where there is no cavity to fill. On a stone home it should be a vapour-open build-up so the wall can keep drying.
Costs run from £10,000 to £50,000. The price of an Ayr job depends on how many walls face the weather and need the full lime and hemp build-up. Rendered brick walls suit a lighter system. Most of what we quote in South Ayrshire sits between £14,000 and £25,000. Home Energy Scotland caps solid wall funding at £7,500, so an eligible household pays around £6,500 on a £14,000 job and £17,500 on a £25,000 one. On a £10,000 job, 75% is exactly £7,500, so an eligible household pays about £2,500. Calum prices every wall from the survey findings rather than working from a single rate.
Each option in the quote comes with its own price and the honest case for it.
Book Your Free Survey ↓Yes. A gable that takes wind-driven rain straight off the Firth of Clyde has to shed far more moisture than a sheltered wall on the same building, so getting the specification wrong costs you more there than anywhere else in the house. We read exposure wall by wall at survey rather than treating every wall the same, then specify from a library of moisture build-ups validated for Scottish wall types. Sealed foam board with a foil face stops a wall like this drying inwards, and that is how damp problems start. It is the main reason people ask does internal wall insulation cause damp.
Calum or Lewis checks for existing damp on the survey visit, so point out any patches you have noticed.
Book Your Free Survey ↓Vapour-open is the technical term for a build-up (lime, hemp and wood wool) that lets moisture pass through and escape rather than sealing it in, which is what most people mean when they say breathable. It is the appropriate approach for solid stone and sandstone walls, and it needs no conventional plastic vapour barrier. We tend to say vapour-open, because it is the more accurate term.
External insulation is usually unacceptable on a sandstone frontage and in conservation areas, so internal vapour-open insulation is normally the route. We will confirm what is feasible for your property.
It depends on the system and on what we find when the old lath and plaster comes off. Plan on about 120mm per insulated wall, and we talk it through room by room at survey.
Solid wall insulation is an eligible measure, though that is not the same thing as every household being approved. Home Energy Scotland covers up to 75% of the cost, capped at £7,500, and an optional interest-free loan of up to £2,500 can sit alongside that grant. Home Energy Scotland decides from the postcode whether an Ayr home counts as rural or island. If it does, the cap for the whole house rises to £9,000. Wall work alone stays capped at £7,500, so the extra only helps if a loft or floor is insulated along with the walls. Funding also requires a TrustMark-registered installer, which we are. Home Energy Scotland assesses the application and confirms eligibility. We answer their questions and hand over the installer documents they ask for.
Check your eligibility with Home Energy Scotland, then book the survey so your application has a written price behind it.
Book Your Free Survey ↓Longer than standard measures: the work is more involved and there is a lot more preparation. Most projects run over a number of weeks, and we give you a clear timeline at quote.
We do, and the exposure reading is often the main thing that changes between them. Alloway sits back from the coast, so its older stone takes gentler weather than a gable near the Ayr seafront. Newton-on-Ayr and Wallacetown sit nearer the water, across the river, and get weather closer to what a west-facing wall in the town centre sees. We survey each property on its own position rather than assuming a fixed answer by postcode, which holds for Maybole and Girvan further south as well. If the ground floor is cold too, that is a separate measure with its own grant cap, and we fit underfloor insulation in Ayr as well.
Book Your Free Survey.
Tell us about your property and we will be in touch to arrange a survey.
Prefer to talk it through first? Call us on 0141 465 5812.



