Internal Wall Insulation in Houston, Renfrewshire: Insulating the 1781 Village Without Sealing It
Internal wall insulation designed from our validated build-up library for pre-1919 stone cottages and villas, with Home Energy Scotland grant funding if you qualify.
-
Stripped to the stone
-
A lime parge
-
Hemp in the frame
-
Wood-wool board
-
Lime plaster with mesh
-
Finished and painted
Illustration: a vapour-open system on a stone wall
-
Stripped to the stone
-
A lime parge
-
Hemp in the frame
-
Wood-wool board
-
Lime plaster with mesh
-
Finished and painted
Solid Wall Insulation in Houston: What the White Render Is Covering
Your Houston cottage is cold, and you worry that insulating it will trap damp in the stone.
-
The worry is fair.
-
The old village cottages are rough stone bedded in lime, and years of repairs have covered much of the original lime render in cement roughcast and modern paint, which let far less damp out.
-
So these walls already dry more slowly than they were built to, and the wrong insulation can tip them into damp.
-
Foil-faced plastic foam board glued onto a cement-rendered stone wall shuts the last way out for that damp.
-
Damp, mould and rot in the floor joist ends can follow within a couple of winters.
The National Audit Office found that, to mid-January 2025, around 98% of external and 29% of internal wall insulation under ECO4 and GBIS carried major defects.
You want the cottage warm without trading the stone for it.
Insulating stone walls like these means protecting the drying route that’s left, so every layer we fit stays vapour-open, from the lime parge coat to the finish plaster.
It is the same internal wall insulation on old stone we fit across Renfrewshire.
If you are turning the attic into a room or building a rear extension, these walls get stripped anyway, so that is the cheapest moment to insulate properly.
The cottage holds its heat, and the old rubble keeps drying out through the lime.
Our process
Our Simple Process for Internal Wall Insulation in Houston
We start with a free survey of your walls, and you see the two systems we fit before anyone strips a wall.
-
Step 1
Free survey and tailored design
Calum or Lewis, our surveyor, looks at every wall: what it is made of, what it is coated in, how exposed it is and any damp. From those notes Calum sets out the layers, drawing on moisture models we have already run. The quote comes back in writing with the reasoning attached, wall by wall.
-
Step 2: the split
The honest comparison
Your wall’s material, finish and modelling decide which of these two systems suits it.
-
Right for most stone
Vapour-open heritage system
Lime + hemp or wood wool
Illustration: vapour from the room passes through each layer and the stone keeps drying. - + Vapour-permeable, the wall keeps drying
- + Largely reversible, and protects the fabric
- + Right for most solid sandstone walls
- − Costs more, takes longer, more prep
- − Slightly more room lost to depth
-
On the right wall
Vapour-controlled system
Pro Clima membrane + insulation
Illustration: the membrane holds vapour from the room back, before it reaches the wall. - + For low-absorption or rendered / painted brick
- + Can be thinner in some cases
- − Only correct where modelling supports it
- − Wrong on a typical absorbent sandstone wall
-
-
Step 3
Specialist installation
Our own installers handle the strip back, framing and insulation. The parge coat and lime finish belong to the lime plasterer who works every heritage job with us. Lime cures between coats on its own timetable, so the programme is honest about that from day one.
-
Step 4
Aftercare and guarantee
The finished work is documented and photographed, and the whole job carries our 25-year workmanship guarantee.
-
Our line in the sand
What we will not do
Sealed foam on solid sandstone
We won’t glue a sealed polystyrene or foam board onto a solid sandstone wall to hit a budget. If that’s what it would take to land a cheaper number, we’ll tell you honestly and recommend against it.
Next step
Start with the survey
See what is under your render before anyone prices the job.
Show us the cold rooms and any patch of damp that keeps coming back, and ask about the grant while we are there.
Book Your Free Survey ↓
Inside the wall
Your wall, insulated layer by layer
Each card shows one build going onto a wall, from bare masonry to a finished room, in the order our fitters work. The pictures are illustrations.
Illustration: heritage system
-
Stripped to the stone
Our fitters strip the old plaster and timber laths back to bare sandstone, so no hidden wood is left to rot. Cornicing on these walls comes down too, and is remade in lime after the insulation goes in.
-
A lime parge
Then a coat of lime, called a parge, goes over the stone. It fills the hollows where damp air could sit and turn to water.
-
Hemp in the frame
Our fitters press two 50mm layers of Scottish-made IndiTherm hemp into a 45mm timber frame fixed over the lime. This is the layer that keeps the heat in your room.
-
Wood-wool board
Wood-wool board, a stiff sheet of bound wood shavings, goes over the hemp next. It gives the lime plaster a solid face to grip and still lets moisture pass through.
-
Lime plaster with mesh
Lime plaster goes on next, with a mesh bedded into it.
-
Finished and painted
A smooth lime finish leaves the wall about 120mm further into the room than before. At handover you get paint guidance, so the finish keeps letting the wall dry.
Hemp, wood wool and lime on bare sandstone
This vapour-open build suits most solid sandstone walls. Each layer lets moisture pass, so the stone behind it can keep drying out.
Illustration: membrane system
-
Stripped back to brick
The old plaster comes off the inside of the wall, back to the brick.
-
Hemp packed into a frame
Our fitters pack hemp insulation into a timber frame fixed over the brick.
-
The Intello Plus membrane
A Pro Clima Intello Plus membrane goes across the frame to keep room moisture out of the wall.
-
Plasterboard and skim
Plasterboard goes over the membrane, and a skim coat finishes the wall.
Hemp and a membrane for the right brick wall
Some walls are brick, and where that brick is rendered or takes up little water, a sealed build can suit it better.
It finishes in plasterboard and a skim coat, so it goes in faster than the lime build.
At your survey, Calum or Lewis checks each outside wall, and Calum tells you which build each one suits.
Why Houston Homeowners Choose Us for Internal Wall Insulation
We design the build-up around how your wall is made and how it handles water. What a heritage install in Houston involves:
-
Solid stone, or 1970s cavity walls
The old village cottages and the buildings near the kirk have solid stone walls. Craigends is a newer estate with cavity walls, which usually need a different job.
-
What goes on the wall, layer by layer
We strip back to bare stone and give it a thin lime coat, then fit two layers of 50mm IndiTherm hemp in a 45mm frame, wood wool board and lime plaster.
-
Designs already tested on walls like yours
Your build-up comes from a library of moisture models validated for rubble, uncoursed, lime-bedded walls like these. The survey confirms which one fits.
-
Membranes only where later brickwork needs them
Later brick or block additions can take a vapour-controlled build-up behind a Pro Clima Intello Plus membrane. Original rubble never gets one.
-
What a room gives up in floor space
Plaster runs straight onto the masonry, so stripping to stone removes the original finish, and the build-up takes depth off every wall we treat.
-
What the survey checks
We look at the frontage first, then open up a window reveal inside to see how the wall is built. Calum writes every quote himself, from our East Kilbride base.
The honest bit: period features
Cornicing, shutters and panelling on the walls we insulate must be removed and cannot be saved. They are recreated once the insulation is in (the cornicing in lime), and at the survey we agree exactly who does that work.
Internal Wall Insulation Cost in Houston, and What the Grant Covers
Internal wall insulation in Houston runs £10,000 to £50,000, most jobs £14,000 to £25,000.
The same survey and systems cover Renfrewshire, including Bridge of Weir, Kilmacolm and Crosslee, and we fit internal wall insulation in Paisley as well.
A cottage has less wall to line than a villa, so cottage scale keeps costs toward the lower half.
- GrantUp to 75%, if you qualify
- Walls cap£7,500 in any postcode
- LoanOptional, interest-free, up to £2,500
- InstallerTrustMark-registered
- Home Energy Scotland grant: if you qualify, up to 75% of the cost, with a £7,500 ceiling on walls that no postcode changes. The £9,000 rural and island figure caps the whole house, so it adds nothing unless a loft or floor is insulated too.
- TrustMark-registered installer required. Home Energy Scotland administers the grant, decides eligibility and confirms which cap applies.
Optional interest-free loan on top, up to £2,500 for solid wall insulation.
Why vapour-open, and why it matters for Scottish stone.
-
1Bare solid stone
Solid sandstone and rubble-stone walls manage water the way they always have: they absorb it and let it evaporate off both faces. They have no cavity, membrane or plastic layer. That works indefinitely, as long as the wall can keep drying.
-
2Foil-faced foam board
Fix foil-faced foam board or sealed foam to the inside and that drying stops. The board makes a cold, sealed layer where warm, damp air from the room reaches the stone, turns to water and has nowhere to go. That trapped condensation is the damp people blame on insulation.
-
3Vapour-open build-up
A vapour-open insulation system (lime, hemp, wood wool) lets that vapour pass through instead, so the wall stays warm and keeps drying. Whether the build-up was designed for your wall matters far more than the brand of insulation.
Calculated, not guessed.
Our designs are built on WUFI modelling, simulating heat and moisture through a build-up over the years a solid wall needs to dry to equilibrium: roughly five years for brick, ten for stone.
-
About 5 yearsbrick, drying to equilibrium
-
About 10 yearsstone, drying to equilibrium
A standard stone wall is matched to a build-up we have already modelled. So before any work starts, we can show you the modelled moisture result for a wall like yours.
What homeowners ask before they commit.
A vapour-open build-up adds some depth, every layer from the parge coat to the plaster taking a little off the face of the wall. On uncoursed rubble the parge depth is not known exactly until we open up, so plan on about 120mm off each wall, within a range of 105mm to 125mm, and we talk it through room by room at survey.
At the survey we work out the depth for each room you plan to insulate.
Book Your Free Survey ↓On a solid-wall job, yes. To strip the wall back we remove the existing cornicing, shutters and panelling on those walls, and they cannot be saved. They are recreated once the insulation is in (the cornicing in lime), and at the survey we agree exactly who does that work.
A vapour-open system protects the fabric and improves the EPC, both of which support the value of a period home. We will give you a straight view of payback for your situation.
Protected, and built to the standard the grant requires.
25-year workmanship guarantee. If our workmanship fails, we put it right. No deposit. We do not ask for money up front. Payment on 7-day terms: invoiced after completion, paid within seven days once you’ve seen the finished work.
-
25-year workmanship guarantee
Given to you in writing.
-
No deposit, pay after completion
No deposit, and payment is due within 7 days of completion.
-
TrustMark and PAS 2030 certified
Audited to the standard the grant requires. Calum designs each job and signs every quote.
-
Our own employed fitters
Never agency labour, and honest advice, with one trusted lime specialist on the finishes. We turn down work that is not right for the wall.
Internal Wall Insulation Questions From Houston and Craigends
Straight answers on cost, damp, render, grants and conservation areas.
Costs run £10,000 to £50,000, most completed jobs £14,000 to £25,000. If Home Energy Scotland approves you, the grant covers up to 75% but stops at £7,500, so a £10,000 job leaves around £2,500 to find and a £14,000 job around £6,500. Old-village row cottages have fewer walls taking weather than a detached villa, so they sit in the lower half of that cost range.
Each option in the quote comes with its own price and the honest case for it.
Book Your Free Survey ↓Done wrong, yes. Damp follows a sealed layer fixed across a solid wall that stops it drying inward, and on a cement-rendered rubble cottage part of the outward route is already gone. Our build-ups stay vapour-open at every layer, and that is what decides whether internal wall insulation causes damp in a stone cottage.
Calum or Lewis checks for existing damp on the survey visit, so point out any patches you have noticed.
Book Your Free Survey ↓Usually not for the work itself. The conservation area protects the street scene, render lines, roofs and boundary walls, none of which internal insulation touches. Individually listed buildings are the exception and can need listed building consent for internal alterations. Check with Renfrewshire Council if your cottage is listed, and we flag it at survey.
Have any earlier consent papers or council letters to hand on the survey day, so we can plan the paperwork around them.
Book Your Free Survey ↓The job can still be done, and it changes what we check. A recoated front leans harder on drying inward, since roughcast and masonry paint pass far less vapour than limewash. We keep the whole build-up vapour-open regardless, and advise on vapour-permeable paint for your next redecoration.
Yes, if the wall is genuinely solid and Home Energy Scotland approves it. The grant covers up to 75% of the cost, capped at £7,500 for the wall work. Rural and island homes can reach £9,000 across the whole house, but only by adding another measure, so plan a Houston wall job on £7,500. An interest-free loan of up to £2,500 can sit on top. It needs a TrustMark-registered installer, which we are. Home Energy Scotland administers and decides, and we provide the documents.
Check your eligibility with Home Energy Scotland, then book the survey so your application has a written price behind it.
Book Your Free Survey ↓Longer than a plasterboard job. Lime sets the timetable: the parge coat and each finish coat need curing time, so a whole cottage typically runs weeks rather than days. A single-storey cottage has no spare floor to retreat to, so we phase the work room by room if you’re living in it.
For most Craigends homes, no. The estate was built from 1973 on the former Craigends House grounds, and stock of that age is cavity-built, insulated cheaply by filling the gap from outside, which is what we quote. A few older properties stand among the newer streets, so where there’s doubt, the survey checks construction at a reveal.
Book Your Free Survey.
Tell us about your property and we will be in touch to arrange a survey.



