Internal Wall Insulation in Lanark: Dressed Front, Rubble Back
Vapour-open internal wall insulation for Lanark’s burgh houses and the flats above the High Street. Each outside wall surveyed separately, backed by a 25-year workmanship guarantee.
Google Review
-
Stripped to the stone
-
A lime parge
-
Hemp in the frame
-
Wood-wool board
-
Lime plaster with mesh
-
Finished and painted
Illustration: a vapour-open system on a stone wall
-
Stripped to the stone
-
A lime parge
-
Hemp in the frame
-
Wood-wool board
-
Lime plaster with mesh
-
Finished and painted
Solid Wall Insulation in Lanark: Two External Walls, Built Two Different Ways
Heating an old stone house or flat in Lanark’s centre costs a lot, and the fear is that insulating it will trap damp and rot the walls.
-
A house here usually has just two outside walls, built two different ways: a dressed ashlar front and a random rubble back.
-
Ashlar is smooth, dense cut sandstone, and rubble is rougher, wetter stone.
-
Neither has a cavity, so both dry out through their lime pointing, harl and plaster, and masonry paint narrows that route further.
-
Foil-backed plastic foam board (PIR) is made for walls with a cavity behind them.
-
Fixed against solid masonry it seals the drying path: trapped moisture shows as damp at skirting level, mould behind furniture and rot in joist ends.
The National Audit Office found 98% of external and 29% of internal wall insulation fitted under ECO4 and GBIS, up to mid-January 2025, had major defects across 30,000+ homes.
Both walls can be insulated safely, and that is the work we do in Lanark. Insulating stone walls like these means keeping every layer open to water vapour.
You may know it as “breathable insulation”, which installers call vapour-open, and it is how we fit internal wall insulation in old burgh houses: lime, hemp and wood wool, each set to the wall it goes on.
Front and back both get warmer, and both keep drying the way stone should.
Our process
Our Simple Process for Internal Wall Insulation in Lanark
We start with a free survey of your walls, and you see the two systems we fit before anyone strips a wall.
-
Step 1
Free survey and tailored design
Calum or Lewis, our surveyor, visits and checks how each wall is built, how exposed it is and any damp already present. Calum then picks the layers from our tested library. The written quote carries the reasoning, wall by wall.
-
Step 2: the split
The honest comparison
Your wall’s material, finish and modelling decide which of these two systems suits it.
-
Right for most stone
Vapour-open heritage system
Lime + hemp or wood wool
Illustration: vapour from the room passes through each layer and the stone keeps drying. - + Vapour-permeable, the wall keeps drying
- + Largely reversible, and protects the fabric
- + Right for most solid sandstone walls
- − Costs more, takes longer, more prep
- − Slightly more room lost to depth
-
On the right wall
Vapour-controlled system
Pro Clima membrane + insulation
Illustration: the membrane holds vapour from the room back, before it reaches the wall. - + For low-absorption or rendered / painted brick
- + Can be thinner in some cases
- − Only correct where modelling supports it
- − Wrong on a typical absorbent sandstone wall
-
-
Step 3
Specialist installation
Our own installers handle strip-back, framing and insulation. The parge coat and lime finish are done by the lime plasterer we use on every heritage job. Lime cures slowly between coats, so the programme is longer than a plasterboard job and says so from the start.
-
Step 4
Aftercare and guarantee
The completed work is photographed and documented, and it carries our 25-year workmanship guarantee.
-
Our line in the sand
What we will not do
Sealed foam on solid sandstone
We won’t glue a sealed polystyrene or foam board onto a solid sandstone wall to hit a budget. If that’s what it would take to land a cheaper number, we’ll tell you honestly and recommend against it.
Next step
We survey and price your front and back walls on their own.
Tell us how you get into the building, close, pend or stair, and ask about cornicing and room depth while we are there.
Book Your Free Survey ↓
Inside the wall
Your wall, insulated layer by layer
Each card shows one build going onto a wall, from bare masonry to a finished room, in the order our fitters work. The pictures are illustrations.
Illustration: heritage system
-
Stripped to the stone
Our fitters strip the old plaster and timber laths back to bare sandstone, so no hidden wood is left to rot. Cornicing on these walls comes down too, and is remade in lime after the insulation goes in.
-
A lime parge
Then a coat of lime, called a parge, goes over the stone. It fills the hollows where damp air could sit and turn to water.
-
Hemp in the frame
Our fitters press two 50mm layers of Scottish-made IndiTherm hemp into a 45mm timber frame fixed over the lime. This is the layer that keeps the heat in your room.
-
Wood-wool board
Wood-wool board, a stiff sheet of bound wood shavings, goes over the hemp next. It gives the lime plaster a solid face to grip and still lets moisture pass through.
-
Lime plaster with mesh
Lime plaster goes on next, with a mesh bedded into it.
-
Finished and painted
A smooth lime finish leaves the wall about 120mm further into the room than before. At handover you get paint guidance, so the finish keeps letting the wall dry.
Hemp, wood wool and lime on bare sandstone
This vapour-open build suits most solid sandstone walls. Each layer lets moisture pass, so the stone behind it can keep drying out.
Illustration: membrane system
-
Stripped back to brick
The old plaster comes off the inside of the wall, back to the brick.
-
Hemp packed into a frame
Our fitters pack hemp insulation into a timber frame fixed over the brick.
-
The Intello Plus membrane
A Pro Clima Intello Plus membrane goes across the frame to keep room moisture out of the wall.
-
Plasterboard and skim
Plasterboard goes over the membrane, and a skim coat finishes the wall.
Hemp and a membrane for the right brick wall
Some walls are brick, and where that brick is rendered or takes up little water, a sealed build can suit it better.
It finishes in plasterboard and a skim coat, so it goes in faster than the lime build.
At your survey, Calum or Lewis checks each outside wall, and Calum tells you which build each one suits.
Why Lanark Homeowners Choose Us for Internal Wall Insulation
We match each build-up to your own wall.
-
Your front and back are surveyed as two separate walls
Street face and rubble rear rarely share a build-up, and we quote the honest, cheaper answer.
-
Every layer set to the wall it is going on
Lime parge first, thick on rubble, thin on ashlar.
- Two 50mm IndiTherm hemp layers in a 45mm frame
- 15mm wood wool board across both faces
- Two coats of lime plaster with mesh
Nothing we fit is tighter than the masonry paint already on the wall.
-
Two tested designs, because you have two walls
We work from a validated library of moisture-tested build-ups, and a Lanark burgh house usually needs two of them, one for tight sandstone and one for loose rubble.
-
Where the membrane route belongs, and where it does not
Hemp behind a Pro Clima membrane belongs on later fabric at the foot of a Lanark plot. It goes on neither the rubble nor a painted ashlar front, and the survey settles which is which.
-
We plan the job around a building you cannot park outside
The work happens inside, so there is no scaffold on the street, and materials come through the close, pend or stair, room by room.
-
What we look at before we come in the door
Calum or Lewis, our surveyor, checks the front’s finish and whether a gable adds a third wall. Calum sets the price.
The honest bit: period features
Cornicing, shutters and panelling on the walls we insulate must come out and cannot be saved. The plaster mouldings are recreated in lime once the insulation is in, and at the survey we agree exactly who does that work, including the timber.
Internal Wall Insulation Cost in Lanark, and What the Grant Covers
Heritage internal wall insulation runs £10,000 to £50,000, and a typical Lanark job costs £14,000 to £25,000.
The same survey and funding route cover Clydesdale, from Carluke to Biggar, and we fit internal wall insulation in Hamilton from the same East Kilbride base.
A rough rubble back wall costs more, because we level it first so the new lining sits flat.
- GrantUp to 75%, if you qualify
- Walls cap£7,500 in any postcode
- LoanOptional, interest-free, up to £2,500
- InstallerTrustMark-registered
If you qualify for the £7,500 grant, that leaves £6,500 to £17,500.
- Wall insulation grants in Lanark run through Home Energy Scotland: up to 75% of the cost, capped at £7,500 for walls, wherever you live.
- On top of that sits an optional interest-free loan, up to £2,500 for solid wall insulation.
- You need a TrustMark-registered installer, which we are, and Home Energy Scotland decides who qualifies.
Rural and island homes have a £9,000 cap across the whole house, which only comes into play when a loft or floor is insulated too.
Why vapour-open, and why it matters for Scottish stone.
-
1Bare solid stone
Solid sandstone and rubble-stone walls manage water the way they always have: they absorb it and let it evaporate off both faces. They have no cavity, membrane or plastic layer. That works indefinitely, as long as the wall can keep drying.
-
2Foil-faced foam board
Foil-faced plastic foam board (PIR) or closed-cell foam glued straight onto the inside of the wall breaks that. It creates a cold, sealed layer where warm internal moisture reaches the stone, condenses, and has nowhere to go. That trapped condensation is the actual mechanism behind the damp people blame on insulation.
-
3Vapour-open build-up
A vapour-open system (lime, hemp, wood wool) lets that vapour pass through instead. With the right design, the wall stays warm and keeps drying. Whether someone designed the build-up to let the wall breathe matters far more than the brand of insulation.
Calculated, not guessed.
Our designs are built on WUFI modelling, simulating heat and moisture moving through a build-up over several years, the time a solid wall actually needs to dry to equilibrium: roughly five years for brick, ten for stone.
-
About 5 yearsbrick, drying to equilibrium
-
About 10 yearsstone, drying to equilibrium
A standard stone wall is matched to a build-up we have already modelled. So before any work starts, we can show you the modelled moisture result for a wall like yours.
Ballagan Farm, Strathblane
A full renovation of a two-storey farmhouse where the walls were damp from being poorly insulated. We stripped them back to the bare stone, parged them in lime, then insulated with IndiTherm hemp and wood-wool boards before finishing in lime plaster across both the sloping ceilings and the solid sandstone walls. The loft was insulated with Knauf Earthwool 44.
Auchinlay House, Dunblane
An internal wall and room-in-roof project for a homeowner preparing to install a heat pump and make the bedrooms comfortable year round. We used a vapour-permeable build-up of hemp, wood-wool board and lime plaster on the walls, paired with a vapour-closed system of PIR and Superfoil SF19+ on the sloping ceilings and dormers, plus Knauf Earthwool in the upper loft space.
Mount Hope, Bridge of Allan
The client was renovating an old sandstone wing of their period property. We installed a vapour-permeable system of 100mm Sisalwool, wood-wool board and lime plaster across four walls, including one large gable wall where the dropped ceiling was removed to create an insulated vaulted ceiling.
Belhaven Terrace Lane, Glasgow
A West End client looking to improve thermal performance across the whole home. The property was given internal wall insulation across the ground floor and room-in-roof insulation in the upstairs bedrooms. A vapour-open design for the stone walls was paired with vapour-closed insulation in the sloping ceilings, keeping the high-absorption sandstone able to dry while stopping warm, moist air reaching the roof spaces.
Observatory Lane, Glasgow
An internal wall insulation project carried out for a client of Oscar J Murray Architects as part of a whole-house renovation in Glasgow’s West End. We used IndiTherm hemp insulation on the stone walls, dormers and sloped ceilings, finished in lime plaster, with a Pro Clima Intello membrane on the sloping ceilings and Contega Solido airtightness tape around the windows.
Protected in Lanark, and built to the standard the grant requires.
If our workmanship fails, we come back and put it right. The invoice arrives after completion and is due within seven days, once you have seen the finished work and the photographs.
-
25-year workmanship guarantee
Given to you in writing.
-
No deposit, pay after completion
Payment is due within 7 days of completion.
-
TrustMark and PAS 2030 certified
Audited to the standards the grant requires, with Calum leading every design.
-
Our own employed fitters
No agency labour and honest advice. We turn down work that is not right for the wall.
Internal Wall Insulation Questions From Lanark and Clydesdale
Straight answers on cost, damp, room loss, grants and conservation areas.
Done correctly, no. Damp problems trace back to vapour-closed materials and cement finishes sealing a wall built to breathe. Our Lanark build-ups, lime, hemp and wood wool, are vapour-open throughout, so the wall keeps drying both ways. That matters most on a rear rubble wall, and it is what settles the worry about internal wall insulation and damp.
Calum or Lewis checks for existing damp on the survey visit, so point out any patches you have noticed.
Book Your Free Survey ↓The full range for heritage internal wall insulation is £10,000 to £50,000, most jobs £14,000 to £25,000. If Home Energy Scotland approves the full £7,500, you pay £6,500 to £17,500. A burgh building’s price depends on how many walls are solid, how irregular the rubble is, and how deep the reveals are. Calum prices each wall from the survey, and the full number is in the quote.
Each option in the quote comes with its own price and the honest case for it.
Book Your Free Survey ↓Often, if the Lanark wall is solid, though approval is never automatic. Home Energy Scotland funds up to 75%, capped at £7,500, plus an optional interest-free loan of up to £2,500 towards solid wall insulation. If your Clydesdale address counts as rural, the cap for the whole home rises to £9,000. Wall work alone still stops at £7,500, so that extra only helps if you add a loft or floor. Home Energy Scotland decides. A TrustMark-registered installer is required, which we are.
Check your eligibility with Home Energy Scotland, then book the survey so your application has a written price behind it.
Book Your Free Survey ↓Vapour-open lime and hemp suits most walls. Random rubble, most Lanark back walls, takes vapour-open internal wall insulation: lime, hemp and wood wool. A painted ashlar street front usually takes it too, since paint has already narrowed its drying route, and the survey confirms which applies. The vapour-controlled route, hemp behind a Pro Clima membrane, suits later fabric like a rear wing.
Often yes, but consent comes first. Lanark’s historic core is a conservation area, and many High Street, Bloomgate, Castlegate and Hope Street buildings are individually listed too. Conservation-area status generally needs no planning permission for internal work. A listed building can still need listed building consent for alterations. South Lanarkshire Council confirms your building’s status, and the survey works out a reversible specification to put to them. We never promise consent.
Have any earlier consent papers or council letters to hand on the survey day, so we can plan the paperwork around them.
Book Your Free Survey ↓Both change, with real numbers before you commit. Cornicing on the wall being stripped comes down. It is recreated in lime once the insulation is in, and at the survey we agree exactly who does that work. Party and internal walls are untouched. Each treated wall comes in by 105mm to 125mm, so plan on about 120mm. Since your two external walls usually sit at opposite ends of the plot, most rooms lose that depth only once. Deep street-front reveals get a thinner build-up so windows still work.
Yes, the whole of Clydesdale beyond Lanark is covered from our East Kilbride base, same survey, build-ups and funding route. Construction varies wall by wall: a Carluke terrace and a Biggar farmhouse each get read on their own. Some rural postcodes get a higher £9,000 grant cap for the whole house, which matters only when a loft or floor goes in with the walls. Home Energy Scotland confirms which postcodes count.
Book Your Free Survey.
Tell us about your property and we will be in touch to arrange a survey.



