Underfloor Insulation in Clydebank: Warm Floors, Whatever Era Your House Was Built
Underfloor insulation in Clydebank for cold ground floors, in the shipyard-era tenements and the post-war rebuild alike: a tidy one-day installation, with up to £1,500 of the cost covered by the grant if you qualify.
Underfloor insulation
-
The cold void
-
Wool between the joists
-
Netting underneath
-
A warmer floor
Illustration: underfloor insulation, step by step
-
The cold void
-
Wool between the joists
-
Netting underneath
-
A warmer floor
A day of underfloor insulation in Clydebank, start to finish
Your ground floor is cold, the skirting lets in a draught, and you have put off fixing it because you dread the floor coming up.
On a Clydebank underfloor job, dust sheets go down before a board is touched. Knauf Omnifit 40 goes in between the joists, and any boards we lift go back down, screwed where they came from. Every room is hoovered before we’re finished.
- Access sets the day. A hatch or crawl space lets the crew work from below. Without one, boards lift in sections.
- Air bricks stay clear, with vent extenders fitted wherever one is blocked.
- We plan access at the survey. Clydebank floors usually close up in one visit.
That void under your boards is ventilated on purpose, and it stays that way. Knauf Omnifit 40 on support netting is how almost every floor insulation job in Clydebank is done, the same underfloor insulation we fit across West Dunbartonshire. If you qualify, the Home Energy Scotland grant pays up to 75% of the cost, capped at £1,500.
On a standard job you get a warmer floor and a tidy room back, usually the same day, with the air under the boards still moving.
What we actually do
What underfloor insulation in Clydebank actually involves
There are two ways to insulate a suspended floor, and they sit at very different price points. The cards below cover both, and what goes into each job.
-
Step 1
Free survey
Survey first A survey of the floor construction, the void (the air space below the boards), and how it is ventilated, so we recommend the right approach for your floor. -
Step 2: the split
One of two ways, picked for your floor
-
The standard job
Knauf Omnifit mineral wool is fitted between the joists and supported so it can’t sag, with the obvious draught paths sealed. A big comfort gain for roughly half the cost of the airtight version.
-
The airtight job
The floor comes up in full. We fit the insulation, then seal it in with a sheet on each side and tape at every join. The best result, where it is practical.
-
-
Step 3
On the day and after
Airbricks kept clear We keep the airbricks and ventilation paths clear so the void keeps working and the timber stays dry.Boards lifted and relaid Where there is no access from below, we lift and relay your floorboards carefully, taking care with period boards.Grant funding and EPC Home Energy Scotland grant funding where you qualify, with help on any questions, and a post-installation EPC where relevant. -
The honest bit: which level your floor needs
The standard job suits most homes. The fully airtight build-up costs more because the whole floor is lifted. We will tell you honestly which your floor and budget call for, not upsell you.
How each system goes in
Underfloor Insulation Fitted Below Your Clydebank Floorboards
Each card below shows one system building up layer by layer, the way we fit it. The pictures are illustrations.
Illustration: standard system
-
The cold void
Each line of light is a gap between your floorboards. Cold air from the air bricks comes up through those gaps and in at the skirtings, into the room you pay to heat.
-
Wool between the joists
We reach the void through one small hatch, and most floors take a day. Knauf Omnifit mineral wool, cut a touch wider than the space between joists, grips them and fills their full depth.
-
Netting underneath
Support netting fixed under the joists holds the wool up, so it can't sag over the years. We photograph it all for you, since you won't be crawling under there to look.
-
A warmer floor
On the first cold Clydebank night after we've been, the boards under your socks feel warmer than they did last winter. Up in the room, the draught at the skirtings eases off and less heat escapes through the floor.
Standard underfloor insulation with Knauf Omnifit
None of this applies to a solid concrete ground floor, and some of Clydebank’s later estates were built that way. You can spot a timber floor from air bricks outside, a bounce underfoot and draughts along the skirtings, the same signs we check before insulating suspended timber floors. We rule a slab out at the survey and point you at the loft or walls instead.
Our most popular option, and superb value where there is access from below. We work in subfloor spaces as shallow as 350mm.
- 150 to 200mm Knauf Omnifit 40, friction-cut to the full joist depth
- Support netting underneath so it never sags, heating pipes lagged
- Airbricks extended where needed, ventilation kept clear, every hatch insulated and screwed back down
- Optional extra sheet and tape to seal out more draughts
Illustration: hemp system
-
Boards up, one room at a time
We lift the floorboards to open up the joists.
-
A hammock between the joists
A thin sheet is slung between the joists and taped round its edges.
-
Hemp cut to fit
IndiTherm hemp is cut to sit snugly in each hammock.
-
Sealed, then boarded
A taped top sheet goes over the joists, then your boards go back down.
Hemp underfloor insulation with airtightness membranes
Hemp goes into the same ventilated void under your floorboards. The air moving through keeps the timber dry, and that same cold air is what chills the room. In Clydebank it is the option to ask about if you want a natural fibre rather than mineral wool.
For a higher-end floor that lets damp out, we install IndiNature IndiTherm hemp between draught-proof membranes, working room by room from above. Highest performance, no compromise on airtightness.
- A membrane that damp can pass through, hung between the joists and taped to the walls
- Every join taped shut, the hemp cut snug to the joists
- A sealed layer over the joists that keeps room moisture out, fitted before the floor goes back
Illustration: PIR board system
-
Battens at your heating level
25mm treated battens are fixed to the joists at your heating design level.
-
Foil-faced board between the joists
PIR is cut tightly to fit between the joists and rests on the battens.
-
Foam edges, taped joins
Foam seals the perimeter and foil tape covers every join.
-
Heating on top
The pipes go in above the board. Then the floor goes back on top.
PIR insulation for underfloor heating
PIR sits under the same suspended timber deck, over the ventilated void that keeps the joists dry. That cold void is what pulls warmth back out of a heated floor. If underfloor heating is going into a Clydebank renovation, this layer has to be in before the deck goes back down.
With underfloor heating you want the warmth reflected upward as well as the draughts stopped. We recommend high-performance foil-faced PIR, and we are happy to work alongside your heating contractor.
- Fitted on 25mm treated battens set to your heating design level, cut tightly between the joists
- Airtightness foam sealing the perimeter, foil tape over every join
- Most heating contractors do not hold TrustMark certification for underfloor insulation, so we fit this element, which keeps up to £1,500 of Home Energy Scotland grant funding open to you if you qualify
Why this is really about airtightness, not “breathability.”
Underfloor insulation fills the gap between your floor joists so the cold void below stops draining heat from the room. How far you take it is the real question.
The void is ventilated on purpose: moisture moves down from the warm room, evaporates into the subfloor air and is carried away, which is why the airbricks have to stay clear. Your insulation has to stop cold air reaching the room and keep warm, moist air out of the timber.
The standard build-up cuts that cold-air infiltration, a real improvement, but it is not airtight. The airtight build-up goes further: an airtight sheet facing the room, a sheet on the ground side that lets damp escape, and tape around the insulation.
- Cuts the cold air rising from the void
- Roughly half the airtight cost
- Quick, and the most common choice
- Membrane upgrade available for airtightness
- Shuts out cold air at every edge
- Keeps moist air out of the structure
- Whole floor lifted, so it costs more
- Not practical for every home
We won’t block the airbricks or seal up the void ventilation to hit a number. That ventilation is what keeps the timber dry, so it stays clear, always.
What underfloor insulation changes in a Clydebank home.
No more draught moving across the floor, a floor that feels warmer underfoot, and rooms that hold their heat for longer.
You feel it most through the colder months, with lower heating bills and a more even temperature across the room.
What homeowners ask before they go ahead.
For the standard job, often not. Where there’s a cellar or crawl space we work from below and leave your floor untouched, otherwise we lift and relay boards carefully. The fully airtight build-up does need the whole floor lifted, which is part of why it costs more. We tell you which applies after the survey.
No, because the void stays ventilated and the airbricks stay clear, that is what carries moisture away. The airtight version goes further and keeps warm, moist air out of the structure in the first place.
Less than most people expect for the standard job, many floors are done in a day or two. Lifting an entire floor for the airtight build-up takes longer, and we’ll scope that clearly.
Floor draughts are one of the most noticeable sources of cold in an older home, so the comfort difference is immediate. We’ll give you a straight view of the payback for your floor.
Often, yes. Underfloor insulation can be funded through the Home Energy Scotland grant. You apply through Home Energy Scotland and we’ll help with any questions.
Underfloor insulation across Clydebank and nearby.
We carry out underfloor insulation across Clydebank and West Dunbartonshire, from standard mineral wool installs to fully airtight floor rebuilds.
Your protection on a Clydebank floor, and the standard the grant requires.
We will tell you honestly if your floor does not need the work, or if something else in the house would make more difference first.
-
25-year workmanship guarantee
Given to you in writing.
-
No deposit, pay after completion
Nothing up front, and payment is due within 7 days of completion.
-
TrustMark and PAS 2030 certified
Audited work that meets the standards the grant requires. Calum approves every quote, whether he or Lewis, our surveyor, did the survey.
-
Our own employed fitters, and a clean site
No subcontractors traipsing through your home, and honest advice. We turn down work that is not right for the floor.
Underfloor insulation: your questions answered.
Straight answers on cost, access, damp, disruption and grant funding.
£1,400 to £2,500 for a standard Knauf Omnifit 40 install, with floor area and how the crew gets in setting where in that range you land, a ground-floor flat’s smaller footprint tends to cost less than a full semi. Should Home Energy Scotland approve a grant, you’d pay about £350 to £1,000. Want the natural option instead? IndiTherm hemp with membranes and airtightness taping runs £3,000 to £5,000, or £1,500 to £3,500 after the grant, and your quote shows both routes priced side by side so you’re comparing real numbers rather than guessing.
Book Your Free Survey ↓Yes, through Home Energy Scotland, if you qualify: up to 75% of the job, capped at £1,500. Separately, you can apply for an interest-free loan for underfloor work, up to £500. The catch that trips people up is the installer has to be TrustMark-registered or the funding doesn’t apply at all, and we are. HES decides who qualifies and confirms it themselves. Our part is answering what you ask and handing over whatever they need from the installer’s side, nothing more than that.
Book Your Free Survey ↓If there’s a hatch or a crawl space, most Clydebank tenement flats sitting on a suspended timber floor need barely a board lifted, and the crew works from underneath with a dust sheet down for the odd one that does come up. Where there’s no way in from below, boards come up in the rooms being worked on and go back down screwed exactly where they came from. Either way, you get a finished floor and a hoovered room back before the crew leaves, not a job left half-tidied for you to finish.
Book Your Free Survey ↓Furniture in the rooms being worked on needs to be clear before the crew starts, that part’s on you. Floor coverings are a different question, and it depends what’s under your feet: fitted carpet usually lifts and relays without trouble, but laminate and glued engineered boards are a longer job, and that’s exactly the kind of thing we settle at the survey rather than a fitter discovering it on the morning with your living room already cleared. Either way, nothing’s left up when the crew goes, boards, carpet or laminate, it all goes back down before they do.
Someone needs to let the crew in and be reachable if a decision comes up mid-job, a blocked air brick that needs a bigger extender, say, but you don’t need to stand over the work. The netting and membranes we use hold everything in place without you doing anything at all. You can get on with your day elsewhere in the house, or pop out and come back to a finished floor, boards down, room hoovered, and photographs sent to you showing exactly what went in underneath.
A standard floor, tenement flat or post-war semi, usually closes up in the one visit. What stretches a job past that is access: a floor where every board across the house has to come up runs longer than one worked mostly from a crawl space below, and that’s the kind of thing that shows up at the survey, not as a surprise on the day. If a job is going to run past one visit, Calum says so on the quote, not halfway through your afternoon.
Yes. West Dunbartonshire is our patch beyond the town boundary too, Old Kilpatrick, Duntocher, Hardgate and Bowling all included, and we work the same run of the Clyde coast down towards underfloor insulation in Greenock. Outside that stretch, just ask, we’ll tell you plainly if your postcode’s covered before you book anything.
Book your free underfloor survey.
Tell us about your floor and we will be in touch to arrange a survey.
Rather talk it through first? Call us on 0141 465 5812.



