For a suspended wooden floor in Scotland, the best underfloor insulation for wooden floors is Knauf Omnifit 40, a glass mineral wool roll friction-fitted between the joists and held up on support netting. A standard job costs £1,400 to £2,500 installed, or £350 to £1,000 where Home Energy Scotland approves a grant. Hemp, rigid PIR board and spray foam each get a straight verdict below, including the one we refuse to fit.
- Knauf Omnifit 40 is our standard under suspended timber floors in Scotland, a flexible, non-combustible roll we fit from below wherever a crew can reach the void.
- Home Energy Scotland funds up to 75% of underfloor insulation, capped at £1,500, so an approved standard job leaves £350 to £1,000 to pay.
- IndiTherm hemp, made in Scotland by IndiNature, goes in from above with Pro Clima membranes and costs £3,000 to £5,000 before the grant.
- Foil-faced PIR board earns its place when a floor is coming up anyway for underfloor heating, at £2,500 to £4,500 installed.
- We never spray foam under floorboards, and since March 2025 no government funding covers the cost of removing it.
- Wood flooring laid straight onto a concrete slab has no void beneath it, so underfloor insulation cannot go in.
If you are standing on cold floorboards weighing up quotes, you will have seen three or four materials recommended, each one by somebody who sells it. We compare the four that come up on Scottish floors on price, on how each one gets into the void and on where each goes wrong. First comes a quick check that your wooden floor can take underfloor insulation at all, and the last section sets out what the grant pays towards each option.
Underfloor insulation for wooden floors: four materials side by side
Two of the four: mineral wool on support netting seen from the void, and hemp batts taped between the joists from above.
Four types of underfloor insulation turn up in quotes for Scottish timber floors, and we fit three of them. The fourth we only meet when we are taking it out.
| Material | What it is | How it goes in | Thermal conductivity (W/mK) | Installed cost | After the grant | Our verdict |
|---|---|---|---|---|---|---|
| Knauf Omnifit 40 | Glass mineral wool roll | Between the joists on netting, from below through a hatch or from above with boards lifted | 0.040 | £1,400 to £2,500 | £350 to £1,000 | Our standard for suspended timber floors |
| IndiTherm hemp with Pro Clima membranes | Hemp fibre batts inside taped membranes | From above, room by room, boards lifted | 0.039 | £3,000 to £5,000 | £1,500 to £3,500 | The natural, airtight upgrade |
| Foil-faced PIR board | Rigid foam board with foil on both faces | From above, cut between the joists on battens | about 0.022 | £2,500 to £4,500 | £1,000 to £3,000, if Home Energy Scotland accepts it as underfloor insulation | The layer under new underfloor heating |
| Spray foam | Foam sprayed onto the underside of the boards and joists | Sprayed from below | Not quoted | We don’t fit it | No government funding to remove it | Never under floorboards |
Thermal conductivity is the W/mK figure on every insulation datasheet. It measures how fast heat passes through the material, and a lower number means you need less thickness for the same warmth. That is why PIR looks so strong on paper. Under a floor, the fit counts as much as the number. Warm air escapes through any gap a material leaves against the joists, and a stiff board in an old floor leaves plenty.
The conductivity figures come from the manufacturers’ datasheets: Knauf for Omnifit, IndiNature for IndiTherm, and a typical foil-faced PIR board for the third row. The prices are our installed bands.
Check that your wooden floor is suspended timber first
A suspended timber floor with the boards up: joists over an open void, before any insulation goes in.
“Wooden floor” covers two different constructions, and from inside the room they can look identical.
Laminate or engineered boards laid straight onto a concrete slab. Nothing sits underneath to fill, so underfloor insulation cannot go in.
Floorboards fixed across timber joists, with a ventilated void underneath. That void is where underfloor insulation goes.
Suspended underfloor insulation for wooden floors only exists for the second kind. Our customers’ reviews mention floors of the suspended kind in a Victorian house, a 1930s bungalow and a ground-floor flat. The flooring on top doesn’t change the answer: carpet, original boards or a click-fit engineered floor over joists all sit on the same void.
If you aren’t sure which construction you have, our guide on how to tell a suspended timber floor from a solid one covers the signs. A survey settles it before anyone writes a quote, and a solid floor rules out every material on this page.
Knauf Omnifit 40: the best underfloor insulation for most timber floors
Omnifit held up on support netting between the joists, photographed from inside the void.
Omnifit 40 is a glass mineral wool roll with a thermal conductivity of 0.040 W/mK, and Knauf classes it Euroclass A1, non-combustible. It arrives perforated, so a crew can split it to suit joists at 400mm or 600mm centres, the two spacings Knauf designs it around.
Joists in older floors don’t always keep to either spacing. A flexible roll copes with that. Pressed into a narrow bay it compresses, and in a wide one it springs back against both joists, so the bay fills without every piece being trimmed to the millimetre. That give is the main reason we choose a roll over a board for work done from inside a crawl space.
- The crew goes in through a hatch. With enough depth to work in, the whole job happens from the void and your flooring never moves.
- The roll goes between the joists. The crew splits it to the bay width and presses it up against the boards.
- Support netting goes across the underside of the joists, holding the roll against the boards so it can’t slump as the years pass.
- The air bricks stay clear. We fit vent extenders where the insulation would otherwise crowd them, because the moving air under the floor keeps the joists dry.
The full specification is on the page for our standard underfloor insulation system.
Omnifit cuts the heat the floor loses and closes the draught routes at the edges, but on its own it does not make the floor airtight. Floors that need that go up to the membrane system in the next section. To see what the netting does and when a membrane is worth paying for, read how the support netting and membranes work under a floor.
A standard Omnifit job costs £1,400 to £2,500 installed, and £350 to £1,000 after the grant.
Find out at a free survey whether a crew can reach your void from below, so your floorboards stay where they are.
Book Your Free Survey →“Both companies initially said there was not much floor space and expected to have to lift the floor, however these guys were able to do it without having to rip everything up and were able to squeeze into the limited floor space.”
Craig Crawford
Google review
IndiTherm hemp with Pro Clima membranes: the natural option
Hemp batts between the joists next to the taped blue Pro Clima membrane, with the floorboards up and the tools still out.
IndiTherm is a flexible batt made from hemp fibre by IndiNature, a Scottish manufacturer, and it carries BBA certification (certificate 23/7060). Its thermal conductivity is 0.039 W/mK, close enough to Omnifit’s 0.040 that the choice between them comes down to the material itself and the membrane system around it.
- We lift the boards and hang a Pro Clima membrane as a hammock between the joists.
- We tape its edges to the perimeter walls and seal every join with airtightness tape.
- The crew cuts the hemp to a friction fit and presses it into each bay.
- A second Pro Clima membrane gets taped over the joists before the floor goes back down.
That seals the floor on both sides of the insulation, which stops the draughts through the gaps between boards as well as the heat loss. It suits homeowners who want non-fossil materials throughout, and floors over a cold, exposed void where every draught path matters.
- The natural system runs £3,000 to £5,000 installed.
- The grant for underfloor insulation is capped at £1,500, so an approved hemp job leaves you £1,500 to £3,500 to pay.
- For a household that wants a warmer floor and nothing more, the standard Omnifit job is the sensible choice, and we will say so at the survey.
Customers also ask about sisal-and-wool batts, and whether sisal or hemp suits a particular floor is a survey conversation.
If a plant-based floor is what you want, the survey prices both systems side by side, in pounds, so you can weigh them up.
Book Your Free Survey →“We were delighted to find an installer who uses a natural, non-fossil fuel-based insulation material like sisal. Calum was very helpful, answering all our questions on the phone.”
Amanda Grimm
Underfloor insulation · Google review
Rigid PIR boards and the best insulation for underfloor heating
Foil-faced PIR boards laid across an open-plan ground floor, with foil tape along the joins.
PIR (polyisocyanurate) is a rigid foam board faced with aluminium foil. A typical board declares about 0.022 W/mK, a little over half the figure of the mineral wool roll, so it reaches the same warmth in less depth.
Every bay gets measured and cut overhead in a crawl space. The board has no give for a joist that bows or leans, and a piece cut 5mm short stays 5mm short, leaving a gap for cold air along its edge.
We fit the boards on 25mm treated battens set to the level your heating design calls for, cut tight between the joists, with airtightness foam around the perimeter and foil tape over every join.
Fitted from below, the finished floor tends to perform worse than its datasheet suggests, so we use a flexible roll there instead. PIR comes into its own when the boards are coming up anyway for underfloor heating. Heat from the pipes or mats needs to go up into the room, and the foil face helps send warmth back upward. Your heating installer then lays the system over the top.
That makes PIR the best insulation for underfloor heating on a timber floor. A PIR job for underfloor heating runs £2,500 to £4,500 installed. If Home Energy Scotland accepts the job as underfloor insulation, the grant brings that to £1,000 to £3,000, and the survey checks how your job fits the rules before you rely on that figure.
If a heating installer is already booked, get us and them talking early, so the battens go in at the height their system needs.
Why we don’t spray foam under floorboards
Spray foam across loft roof timbers, flagged on a survey. The timber behind it is out of sight.
We take spray foam out of Scottish homes. We don’t put it in, under floors or anywhere else.
Sprayed onto the underside of a floor, the foam bonds to the boards and the joists. Once it has set, nobody can see the timber behind it, so a surveyor has no way to check for rot or woodworm, and closed-cell foam holds moisture against the wood it covers. Sprayed near the air bricks, it can also choke the airflow that keeps the void dry.
- The vast majority of mainstream mortgage lenders refuse or heavily restrict homes with spray foam. A minority of specialist lenders consider them only under strict conditions.
- Lender and surveyor guidance concentrates on roofs, where most spray foam went, but the objection under a floor is the same: nobody can inspect the timber.
- In Scotland, much of that foam went in under earlier grant and loan schemes. Since March 2025 there has been no government funding for removal, so the homeowner pays.
- Certified removal restores a home’s mortgageability in most cases, though it is never guaranteed, and taking the foam off can uncover timber decay hidden underneath.
If you have found foam under your floor, or a survey has flagged it, start with an inspection. Our spray foam removal service page sets out how we assess it and when removal is needed.
Choosing underfloor insulation for wooden floors, and what the grant pays
Mineral wool fitted between the joists across a whole room, ready for the floorboards to go back down.
- Is underfloor heating going in? The floor is coming up anyway, and foil-faced PIR is the layer to put under it.
- Do you want plant-based materials and an airtight floor? IndiTherm hemp with the Pro Clima membranes, fitted from above, is the system for you.
- Can a crew reach the void from a hatch? Omnifit goes in from below and the boards stay down. Without access, boards come up in sections and the same roll goes in from above.
- Is the floor solid concrete? None of these materials applies, and we tell you so at the survey.
The grant works the same way whichever material you pick.
the largest share of the cost the Home Energy Scotland grant pays for underfloor insulation
the grant cap for underfloor insulation, whichever material goes in
Home Energy Scotland grant rules, checked against homeenergyscotland.org on 19 August 2026. Eligibility is confirmed when you apply.
- Every measure at one property shares a combined cap of £7,500.
- An optional interest-free loan adds up to £500 for underfloor insulation.
- The work must be done by a TrustMark-registered installer, and Home Energy Scotland reviews and decides every application.
We are TrustMark registered and PAS 2030 accredited, and every job carries a 25-year workmanship guarantee. We take no deposit, and payment is due within 7 days of completion. For the price of each measure worked through with the grant, see a full breakdown of underfloor insulation prices.
The survey looks under your floor, picks the material that fits it and puts the price and the grant figure in writing.
Book Your Free Survey →“Calum did an initial survey and explained the insulation process clearly and communicated a reasonable price back to me quickly.”
David Goldring
Loft and underfloor insulation · Google review
Frequently asked questions
Two of the materials compared above: hemp batts between joists, and PIR board laid along a hallway.
What is the best insulation to use under a wood floor?
For a suspended timber floor, a flexible mineral wool roll such as Knauf Omnifit 40. It fills uneven bays between old joists, sits on support netting, and costs £1,400 to £2,500 installed, or £350 to £1,000 after an approved Home Energy Scotland grant. Hemp suits homes that want natural materials, and PIR suits a floor that is getting underfloor heating.
What kind of underfloor insulation is suitable for existing timber floors?
Flexible insulation that can be friction-fitted between the joists. Knauf Omnifit 40 is our standard and can go in from below without lifting the boards where there is access. IndiTherm hemp with Pro Clima membranes also suits existing floors, fitted from above with the boards lifted room by room.
Can you use PIR board under floorboards?
Yes, and it works best when the boards are already up. Cut between the joists on battens, with every join foil-taped, PIR makes a good layer under new underfloor heating. Fitted from below under an existing floor, the rigid board leaves gaps against uneven joists, so we use a flexible roll there instead.
What is the best insulation for underfloor heating on a timber floor?
Foil-faced PIR board, fitted between the joists on treated battens set to the heating design level, sealed with airtightness foam at the perimeter and foil tape on every join. The foil face helps send heat up into the room. Installed, it runs £2,500 to £4,500 before any grant.
Is spray foam insulation under floorboards a good idea?
No. It bonds to the boards and joists, hides the timber from any surveyor, and closed-cell foam holds moisture against the wood. The vast majority of mainstream lenders refuse or heavily restrict homes with spray foam, and since March 2025 no government funding covers removing it. We remove spray foam and never install it.
Does the Home Energy Scotland grant cover hemp underfloor insulation?
It can, on the same terms as the standard system. Home Energy Scotland funds up to 75% of the cost, capped at £1,500 for underfloor insulation, so on an approved £3,000 to £5,000 hemp job you pay £1,500 to £3,500. A TrustMark-registered installer is required, and Home Energy Scotland decides every application.
Bring the question this list misses to your free survey, and we will answer it with your own floor open in front of us.
Book Your Free Survey →“Explained everything in great detail and answered all my many questions. The work was done quickly, to a very high standard and the team were incredibly tidy.”
Gill Taggart
Underfloor insulation · Google review
Get a material recommendation for your own floor
The right material depends on what is under your boards, how you reach it and what you plan to do with the floor next.
A free survey answers all three for your own house, and you get the recommendation and the price after grant in writing.
Or call us on 0141 465 5812







