What is room in roof insulation? It is the work that lines every side of an attic room with the weather behind it: the sloping ceilings (the skeilings, in Scots), the short stud walls, the cold voids behind and above them, the dormers and the gable. A bedroom downstairs might have one outside wall. An attic room can have two slopes of roof, a dormer and a gable end around it, with little more than plasterboard, timber and slates between your bed and the weather.
- Heat leaves an attic room through its sloping ceilings, its short stud walls, the cold voids behind and above them, its dormers and any gable facing the weather.
- Skeiling is what plenty of Scots call the slope of an attic room’s ceiling, and it sits right under the slates.
- Warm, damp air that slips through gaps into a cold roof turns to water there, so the room side needs an airtight layer and the roof side needs moving air.
- Our PIR and hemp systems keep 50mm of open air between the insulation and the roof, so the roof keeps its air path from the eaves upwards.
- Home Energy Scotland treats room in roof insulation as its own measure, with grant of up to £3,000, set apart from the £1,500 limit for loft insulation.
- From our East Kilbride base we survey attic rooms across Glasgow and Lanarkshire, and the survey settles whether your sloping ceilings stay up or come down.
A room in the roof with sloping ceilings on both sides and a roof window.
Calum Farquhar, who owns the company, describes a poorly insulated loft conversion as a room you cannot keep comfortable “whether the sun is splitting the rocks or your driveway is frozen solid”. If yours is the bedroom nobody wants in January, or the one you give up on in a July heatwave, the cause sits in a handful of surfaces, and each one has a fix.
What is room in roof insulation, and what counts as a room in the roof?
A dormer attic stripped back: the roof timbers, the cheeks of the dormer and the low stud walls are all on show.
A room in the roof is a room built into the space under a pitched roof. Some went in when the house was built, and others arrived decades later as loft conversions. From the inside you know one at once: part of the ceiling follows the line of the roof before it flattens out near the top, and the side walls are too short to stand against.
Room in roof insulation is insulation fitted to every cold surface of that room, plus the unheated spaces wrapped around it. A full job treats the parts below together, because heat leaves by whichever surface gets missed.
Skeilings.
The sloping ceilings that follow the rafters from the top of the side walls up towards the flat ceiling. Estate agents often call them coombed ceilings.
Stud walls.
The short upright walls along each side, framed in timber where the roof gets too low to stand. You may hear them called dwarf walls or knee walls.
Eaves voids.
The triangular spaces behind the stud walls, running down to where the roof meets the outside wall. Many have a cupboard door and a lot of stored boxes.
The flat ceiling.
The level strip at the top, fixed under the collar ties, with a small loft space above it.
Dormers.
The boxes that push out through the roof slope to hold a window, each with a front, two side cheeks and a roof of its own.
The gable.
The end wall of the room where the roof stops. If it faces outside, it is an outside wall like any other.
Calum’s own list is shorter: sloping ceilings, dormers, stud walls and residual loft spaces, his name for the eaves voids and the space over the flat ceiling.
In Glasgow, Lanarkshire and Edinburgh you find rooms in the roof in storey-and-a-half cottages and villas built with dormers, in semi-detached houses whose lofts were converted later, and in top-floor flats where the attic became a bedroom. How cold the room runs depends on what went behind its plasterboard when it was made.
Skeiling ceilings: why the slopes run cold in winter and hot in summer
A plasterboarded sloping ceiling, the skeiling, with a roof window set into it.
Look up at a skeiling and you are looking at the underside of the roof. Behind the plasterboard, or the old lath and plaster, sit the rafters, then the sarking boards or roofing felt, then the slates. In a conversion built with thin insulation between those rafters, or with none, the heat from your radiator rises, gathers under the slope and passes out through it.
The slopes are the biggest cold surface in a typical attic room, so sloping ceiling insulation takes up much of a room in roof job. The rafters limit what fits: they are only so deep, and whatever goes between them has to leave room for air to move under the slates.
In summer the same slope works the other way. Slates sit in the sun all afternoon and heat up, and with so little between them and your ceiling, that heat comes down into the room. A skeiling ceiling with good insulation behind it slows heat travelling in either direction, so the room gains less in July as well as losing less in January.
Calum rates hemp highest for the summer side of the problem. Hemp holds heat in its own mass, which steadies the room through a hot spell, and he describes the hemp method as performing well at both extremes of the year.
On the next frosty evening, put the back of your hand flat on the skeiling, then on an inside wall downstairs. The difference you feel is heat leaving through the roof.
Dormer cheeks, stud walls and the eaves behind them
Plasterboard on the slopes and board on the dormer cheeks.
A dormer sticks out of the roof into the wind and rain on three sides and on top. Its cheeks, the two triangular side walls, are often a thin timber frame with lead, slate or cladding on the outside, and its roof is often flat with a shallow void under it. In effect the dormer is a small box of outside walls attached to your room, and on a cold night you can feel the chill coming off the cheeks beside the window.
Dormer insulation is fiddly because space is tight at the window reveals and inside the cheeks. Over-boarding fixes insulated plasterboard round the dormer over its existing surfaces. In our PIR and hemp methods we strip the dormer back first, and where a second layer of hemp will not fit at a cheek or a reveal, a 20mm Marmox insulation board goes on in its place.
The stud walls have a different problem. Behind each one sits an eaves void, a space open to the roof and as cold as the loft. Only the stud wall and its plasterboard stand between that void and the room, and the floor of the void is the ceiling of the room below, so heat leaks up into it from downstairs too. A cupboard door in the stud wall adds a draughty gap round its frame.
Whichever method you choose, we insulate the stud walls and those residual loft spaces too, cutting access first if an eaves void has no way in. Knauf Earthwool 44 goes there on over-boarding and PIR jobs, while a hemp job gets IndiTherm hemp, 200 to 250mm deep in the voids and two layers thick on the stud walls.
At the ends of the room, a gable that faces outside is as exposed as any outside wall in the house, and the survey looks at it with the rest of the room.
The biggest surface warms up, while the dormer cheeks, the stud walls and the eaves behind them stay cold, and the room keeps its cold corners.
Slopes, dormer cheeks and reveals, stud walls, eaves voids, the space above the flat ceiling and any outside gable all go into one job, so no surface is left to be the cold one.
At a free survey we open your eaves cupboard, check round the dormer and tell you which surfaces are letting the cold in.
Book Your Free Survey →“Insulation and flooring of two awkward eaves spaces. From initial visit to house to provide quote we got impression of good understanding and knowledge of work required and price quoted compared favourably.”
Lynne Swan
Insulation and flooring of two eaves spaces · Google review
Condensation in a room in the roof, and why the air behind the insulation has to move
Foil battened across the rafters of an attic room, the airtight layer.
Condensation is what you see on a cold window after a shower. Warm air carries moisture you cannot see, and when it touches something cold, that moisture turns back into water. Cooking, washing, drying clothes and breathing all add moisture to the air in a house, and warm air rises, so the attic room gets its share.
In a room in the roof the coldest surfaces are out of sight: the underside of the slates and sarking, the rafters, and the inside of the eaves voids. If warm air from the room finds a way through gaps in the ceiling, round a downlight or past the edge of a cupboard door, it reaches those cold timbers and leaves water on them where nobody looks. Left long enough, wet roof timbers give mould and rot the conditions they need.
Badly fitted insulation can make that worse. Pack insulation hard against the underside of the roof, or leave old insulation blocking the air path from the eaves, and the roof side has no way to dry out.
A room in the roof stays dry when two things work together. On the room side, an airtight layer stops warm, damp air getting into the roof at all. On the roof side, a clear air path lets outside air run from the eaves to the top of the roof and carry moisture away.
That is why our PIR and hemp methods keep 50mm of open air between the insulation and the roof, so the air path between the eaves and the upper loft stays clear. Over-boarding leaves the existing slopes where they are, so before we suggest it, we check at the survey whether air can still move above them. Where old insulation already blocks that path, it has to come out.
- The roof. Slates over sarking or felt, as they are now.
- A 50mm air gap. Left open behind the insulation for the air coming up from the eaves.
- PIR board. A rigid foam insulation board, cut to fit between the rafters, with every join sealed in foil tape.
- Superfoil SF19+. A multifoil laid over the whole surface as the airtight layer, with some insulation of its own.
- Battens. Fixed over the foil to hold the seal and carry the plasterboard.
- Plasterboard and skim. Taped and skimmed with multifinish plaster, ready for you to decorate.
The hemp method does the airtight job with a Pro Clima Intello Plus membrane across every stripped surface, Tescon Vana tape on its joins and Contega Solido tape round the edges and window frames.
Whatever goes into the roof, an extractor fan in an attic shower room still earns its keep, and so does a window opened after a bath.
Loft room insulation and loft insulation: how the two jobs differ
PIR board between the rafters of the slopes, with mineral wool in the loft spaces beside the room.
Ordinary loft insulation goes on the floor of a loft nobody lives in. Our standard loft insulation job lays 300mm of Knauf Earthwool 44 in two layers between and over the joists, and the loft above it stays a cold, ventilated space.
Loft room insulation turns that around. The room belongs to the heated house, so the insulation has to follow its shape: up the slopes, down the stud walls, across the flat ceiling and round the dormers, with the leftover loft spaces treated as well. Attic room insulation, room in roof insulation and loft room insulation are three names for that one job. Home Energy Scotland treats it as a separate measure from loft insulation, with its own grant cap.
On cost, our typical prices for a room in roof job run from £5,000 for over-boarding to £18,000 for hemp, before any grant. If you qualify, the Home Energy Scotland grant pays as much as 75% of what the work costs, with a £3,000 ceiling for room in roof insulation (loft insulation has a separate £1,500 ceiling), and an optional interest-free loan for the measure goes up to £1,000. The scheme funds the work only through a TrustMark registered installer.
Calum matches our three systems to your budget and to what he calls your “appetite for upheaval”.
Over-boarding.
Your ceilings stay up. Insulated plasterboard goes over the existing slopes and round the dormers, or else a 25mm batten, a sheet of multifoil, another 25mm batten and new plasterboard. The cheapest route, with the least disruption.
PIR with Superfoil.
The slopes and dormers come back to the rafters. PIR goes between them with the 50mm air gap behind and Superfoil SF19+ over the top. By Calum’s reckoning, that fits 200 to 300% more insulation into the slopes than over-boarding does.
IndiTherm hemp.
Also stripped back to the rafters. Hemp fills the gaps between them, a second layer goes between 45mm counter-battens fixed across the rafters, and an Intello Plus membrane seals the room before the plasterboard. Calum’s pick for comfort at both ends of the year.
All three finish with the new boards taped and skimmed in multifinish plaster. You can see each method in photos from our own jobs on our room in roof insulation page.
Book a free survey for a written quote that can set two or three options for your attic room side by side, with the pros and cons of each.
Book Your Free Survey →“I would highly recommend this company for loft and eaves insulation. They turned up on time every day …”
Hilda De Groot
Loft and eaves insulation · Google review
What a survey checks before anything is opened up
Old fibreglass and plasterboard pulled out of an attic, the kind of find a survey looks for behind the slopes.
Nobody can see inside a slope from the room, so at the survey we go into the eaves voids and the loft space above the flat ceiling wherever there is a way in. We check how deep the rafters are, what the slopes are made of, whether old insulation is blocking the air path from the eaves, and how much room the dormer cheeks and window reveals leave.
Then comes the question that decides your options: can your ceilings come down? Where air already moves through the rafters, adding insulation at the ceilings can save you the cost of opening the room up. Where old insulation is jammed against the roof, it has to come out whichever system you pick. Some households keep their ceilings and accept a thinner build-up, others put up with the dust for a warmer room, and you make that call with us at the survey.
Sometimes the answer is that a room needs little. Where a conversion was insulated well, with clear ventilation and an airtight layer still intact, adding more makes a small difference, and we tell you that at the survey.
Some households add the main loft or the ground floor at the same time, and our guide to loft and underfloor insulation in one visit covers that pairing.
- On a cold evening, does the slope or the stud wall feel colder to your hand than a wall downstairs?
- Inside the eaves cupboard, is there insulation on the floor and on the back of the stud wall, or bare boards and plasterboard?
- Do you see dark patches or mould in the angle between slope and stud wall, or round the dormer window?
- Is there a hatch into the loft space above the flat ceiling?
- Does the room overheat on sunny afternoons, as well as running cold in winter?
What is room in roof insulation: common questions
A finished attic room with plastered slopes around a bay window.
What is room in roof insulation?
Insulation for every cold surface of a room built into the roof. That covers the sloping ceilings, the stud walls, the eaves voids behind them, the loft space over the flat ceiling, the dormers and any gable facing outside, so insulation wraps the whole heated room.
What is a skeiling?
A Scots name for the sloping ceiling of an attic room. It is the part of the ceiling that follows the roof, between the top of the short side wall and the flat ceiling. Coombed ceiling and sloping ceiling describe the same surface.
Why is my attic room so cold in winter?
It has more cold surfaces around it than other rooms in the house. The slopes, dormers and any outside gable face the weather, and the stud walls back onto cold eaves voids. With little insulation behind them, heat from your radiator rises into them and leaves through the roof.
Can you insulate a dormer from inside?
Yes. Over-boarding fixes insulated plasterboard round the dormer, over its existing surfaces. Our PIR and hemp methods strip the dormer back and insulate inside the cheeks, and where a reveal or cheek is too tight for a second layer of hemp, we fit 20mm Marmox insulation board in its place.
Is room in roof insulation the same as loft insulation?
No. Loft insulation lies on the floor of an unheated loft, and the space above it stays cold. Room in roof insulation wraps a room you heat, slopes, stud walls and dormers included. Home Energy Scotland funds them as separate measures, so each has its own grant cap.
Will room in roof insulation cause condensation?
It should not, if the room side is airtight and the roof side keeps its air path. Roof condensation starts when warm, damp air reaches cold timbers. Our PIR and hemp methods seal the room side and keep a 50mm gap open behind the insulation, and any old insulation blocking the air path comes out first.
Can room in roof insulation be done without taking the ceilings down?
Often, yes. Over-boarding leaves your ceilings up and adds insulation over them. It depends on what sits behind the plaster: if old insulation is blocking the air path above the rafters, that part has to come out, and we tell you at the survey which applies.
Show us the cold corner, the eaves cupboard and the slope that bakes in July, and at a free survey we will tell you what sits behind each one.
Book Your Free Survey →“We have an old flat with a loft conversion that had very little insulation. … We agreed on insulating both the walls and the ceiling and we’re already noticing a difference in the temperature with the recent hot weather.”
C Harper
Loft conversion insulation · Google review
Plastered slopes and dormer cheeks in a room in the roof.
Find out what sits behind your sloping ceilings
We go into the eaves voids and the loft space over the flat ceiling, measure the rafters, look at each dormer and check whether air can still move under your roof.
We email your quote after the visit, with the options your room can take.
Or call us on 0141 465 5812







